Instructions

1. Brow preparation
Clean your brows thoroughly and avoid oil-based products.

2. Applying the perm serum
Apply the perm serum to your brows with a micro applicator.
Brush the hairs upward with the Y-comb or brush.
Processing time: 4–8 minutes (the finer the hair, the shorter the time).
Note! Don't leave the perm serum on for more than 8 minutes to avoid damaging the brow hairs. The first time, we recommend sticking to a shorter time and then testing which processing time works best for you.

3. Applying the fix serum
Wipe your brows with a dry cotton pad.
Apply the fix serum to your brows.
Processing time: 4–8 minutes (the finer the hair, the shorter the time).
Note! Don't leave the fix serum on for more than 8 minutes to avoid damaging the brow hairs. The first time, we recommend sticking to a shorter time and then testing which processing time works best for you.

4. Brow tinting
Clean your brows carefully and tint them with the LIFTÉ chemical tint.

5. Applying the nourish serum
Apply the nourish serum to your brows. Leave it on for 3-5 min. Clean your brows.

6. Aftercare
Avoid getting your brows wet for 24 hours after lamination so the result lasts as long and looks as good as possible. Between treatments, it's important to use a moisturizing serum to keep the hairs healthy and stop them from getting frizzy or dry.

1. Lash preparation
Clean your lashes and eyelids thoroughly (avoid oil-based products) and make sure they are dry, so the glue sticks better.
Choose a silicone shield with the right curve. Size S has the sharpest curve, M is medium and L has the softest curve. If the shield is too big, trim the sides to make it narrower.

2. Attaching the silicone shield
Put glue on the back of the silicone shield and attach it to your upper eyelid. Press it for about 15-30 seconds so it stays in place. Feel free to add more glue to the corners if any part comes loose.

3. Attaching the lashes to the shield
Apply glue to a small section of the silicone shield (ideally start from the middle) and attach your lashes to it. Work in small sections and don't apply glue to the whole shield at once - this way the glue stays fresh and the lashes stick better. Comb the lashes straight up with the Y-comb and make sure any lashes that are stuck together or crossed are separated. Every lash should be attached to the shield pointing straight up.

4. Applying the perm serum
Apply the perm serum to your lashes with a micro applicator. Cover the lashes from the root to the middle of the lash. Note! Don't put the perm serum on the tips of the lashes!
Processing time: 5–8 minutes (the finer the hair, the shorter the time).
Note! Don't leave the perm serum on for more than 8 minutes to avoid damaging the lashes. The first time, we recommend sticking to a shorter time and then testing which processing time works best for you.

5. Applying the fix serum
Wipe the lashes with a dry cotton swab.
Apply the fix serum to your lashes with a micro applicator. Cover the lashes from the root to the middle of the lash. Note! Don't put the fix serum on the tips of the lashes!
Processing time: 5–8 minutes (the finer the hair, the shorter the time).
Note! Don't leave the fix serum on for more than 8 minutes to avoid damaging the lashes. The first time, we recommend sticking to a shorter time and then testing which processing time works best for you.

6. Lash tinting
Remove the fix serum thoroughly with a dry cotton swab and tint your lashes with the LIFTÉ chemical tint.

7. Finishing and removing the silicone shield
Clean your lashes carefully and remove the silicone shield.
Apply the nourish serum to your lashes, leave it on for 3–5 minutes and gently wipe it off. Your lashes are now beautifully curled and cared for.

8. Aftercare
Avoid getting your lashes wet and using mascara for 24 hours after lamination so the result lasts as long and looks as good as possible. Between treatments, it's important to use a moisturizing serum to keep the hairs healthy and stop them from getting frizzy or dry

1. Cleanse your brows.

2. Mix equal parts tint and developer.

3. Apply the tint with the applicator in your desired shape.

4. Leave it on for 10 to 15 minutes.

5. Remove the tint with a cotton pad.